Kverneland Exacta TL GEOSPREAD
GPS controlled, intelligent spreading (into a minimum of 1 metre sections) with the Exacta TL GEOSPREAD.
Highlights
CentreFlow spreading system Weighing system with unique reference sensor Prevent overlap with the GEOSPREAD system Section control with 1 metre sections MULTIRATE: multiple rates within a working widthDescription
A Perfect Spreading Result!
With Kverneland Exacta TL GEOSPREAD you will get a perfect spreading result! The GEOSPREAD system does section control with sections of only 1 metre. With a maximum of 54 sections and the possibility to switch sections over the middle, unnecessary overlap is set to an absolute minimum. The 4 load cells and reference sensor on the Exacta TL GEOSPREAD are important features as with section control accurate weighing is essential. The total benefit of GEOSPREAD combined with speed related spreading and GEOPOINT headland management can be up to 15%. This can be achieved by saving fertiliser and better yields, because of no unnecessary overlap. In combination with MULTIRATE, the variable rate application, which applies multiple rates within a working width even more cost effective spreading can be achieved. This Kverneland Exacta TL GEOSPREAD spreader is ISOBUS compatible and AEF certified. You can operate the spreader in combination with the IsoMatch Tellus PRO, IsoMatch Tellus GO+ or any other ISOBUS compatible tractor terminal.
The Advantages:
- CentreFlow spreading system
- Fully automatic weighing system with unique reference sensor
- Unique GEOSPREAD system with two electric actuators
- Section control with 1 metre sections up to a maximum of 54 (depending on the terminal functionality)
- ISOBUS 11783 compatible for easy plug and play
- Possible in combination with IsoMatch GEOCONTROL
- MULTIRATE to apply multiple rates within the working width
Technical Specifications
Exacta TL GEOSPREAD (narrow) |
TL 1500 |
TL 2150 |
TL 2800 |
TL 3450 |
Hopper capacity (l) |
1500 |
2150 |
2800 |
3450 |
Filling height (cm) |
119 |
138 |
157 |
176 |
Width (cm) |
275 |
|||
Filling width (cm) |
269 |
|||
Empty weight (kg) |
655 |
685 |
715 |
745 |
Spread width (m) |
12 - 54* |
|||
Output (kg/min) |
10 - 320 |
* Depending on fertiliser type and type of vanes.
Exacta TL GEOSPREAD (wide) |
TL 1875 |
TL 2550 |
TL 3225 |
TL 3900 |
Hopper capacity (l) |
1875 |
2550 |
3225 |
3900 |
Filling height (cm) |
119 |
138 |
157 |
176 |
Width (cm) |
290 |
|||
Filling width (cm) |
284 |
|||
Empty weight (kg) |
695 |
725 |
755 |
785 |
Spread width (m) |
12 - 54* |
|||
Output (kg/min) |
10 - 320 |
* Depending on fertiliser type and type of vanes.
Features
When running IsoMatch GEOCONTROL in addition to GEOSPREAD you can set the Exacta CL, TL and TLX GEOSPREAD more accurately. The working width will be automatically adjusted to suit the overlap and coverage using a GPS positioning system. For example, when driving in a wedge or irregular shaped field, GEOSPREAD will start to decrease the working width step by step. GEOSPREAD is using the section control function of the IsoMatch GEOCONTROL software which is in the IsoMatch Tellus PRO or IsoMatch Tellus GO+ terminal. The spreader working width is divided into a minimum of 1 metre sections (max. 45 sections on TLX GEOSPREAD, max. 54 sections on TL GEOSPREAD and max. 33 sections on CL GEOSPREAD). Not only the spreading width is adjusted, the application rate (kg/min) is also adjusted automatically to match the revised spreading width. This unique combination of working width and application rate adjustment makes the GEOSPREAD system extremely accurate, with minimum influence on the spread pattern coefficient of variation.
The Advantages:
- Quick and accurate spreading, due to the actuators being directly connected to the discharge point. No linkages.
- Stable disc RPM in combination with discharge point adjustment maintains the spreading pattern (coefficient of variation)
- Section control with 1 metre sections (depending on the terminal functionality)
- Easy operation; no need to step off the tractor to adjust the working width
- 100% ISOBUS compatible for easy operation
- Automatic start/stop with GPS on headlands possible
For easy and cost effective spreading
MULTIRATE (Variable Rate Application) applies multiple rates within a working width.
In order to spread the right amount of fertiliser at a specific place in a field there is a need to have a different rate within the working width. Depending on the field variation and the size of the grid of the variable application map, input of 2, 4, 6 or 8 rate sections can be used. This means a more accurate application of nutrients to have a better nutrient efficiency, better yield and reduce costs.
With a Kverneland GEOSPREAD spreader you invest in 100% ISOBUS compatibility for easy plug and play with the IsoMatch Tellus PRO or any other AEF certified terminal. In just some steps with this combination you are ready to use MULTIRATE. You have to convert a satellite or soil map into an ISO-XML file. Download the Variable Rate Map into the terminal and you are ready to spread with MULTIRATE with 2 up to 8 rates.
- No impact, no fragmentation, no dust: Central release point, smooth acceleration and centrifugal force accelerates fertiliser up to disc speed before it reaches the vane.
- Accurate spreading pattern: A double overlap spreading pattern gives unrivalled accuracy. The 8 vanes per discs are ensuring a continous flow of fertiliser to the field. This is important for high capacity spreading and forward speed.
- Minimal wind influence, maximum tolerance: Flat discs and a horizontal flow of fertiliser give a symmetrical spreading pattern.
- Consistent spreading pattern: Eight vanes per disc, eight sectors per revolution give an equal distribution. Double overlap spreading pattern.
- Guaranteed accuracy on slopes: guaranteed accuracy on slopes. The fertiliser always contacts the vanes at the same point, also on slopes and travels the complete length of the vane.
- Continuous dynamic "online - calibration" with high frequency communication signal.
- Kvernelands unique reference sensor technology: all negative influences are automatically corrected and eliminated, ensuring utmost spreading accuracy even on hill sides. The Kverneland reference sensor gives you absolute accuracy, because every kilo counts!
- Load cells in combination with the unique reference sensor:
- Auto calibrating and continuous weighing system
- Automatic correction on slopes
- Automatic correction of shocks, even on rough terrain
- Automatic speed related dosing system
- No calibration test needed
- Highest accuracy in all conditions: even spreading quality guaranteed! Save costs and increase quality!
- The compact EasySet 'dashboard' gives you considerably simplified accurate setting and adjustment of application rates. Two hydraulically operated metering plates, each with three discharge openings ensure an equal fertiliser flow from the hopper to the spreading discs.
- The development department of Kvernelands spreader R&D team has its own spreader competence centre in order to allow continuous testing throughout the year. All test are carried out according to the strictest international standards and quality requirements.
- The key to accurate spreading is matching fertiliser quality and litre weight with the spreading charts as close as possible. The Kverneland Exacta checklist helps you to ensure consistent accuracy in all field conditions
1. Select fertiliser type
2. Determine granule size and distribution
3. Determine litre weight
- Direct access to the most recent test results at: www.kvernelandspreadingcharts.com or download the spreading charts Application via the App Store or get it on Google Play
With the AutosetApp you have always the most up to date settings for your weighing spreader available. The AutosetApp is an App (software application) available on the IsoMatch Tellus PRO or IsoMatch Tellus GO+ terminal. The AutosetApp is standard integrated into the IsoMatch GEOCONTROL software. This App connects the terminal directly with the GEOSPREAD weighing spreader and will automatically adjust the spreader according to the settings entered into the App. The AutosetApp will also work in combination with the CL-EW and TL, with the exception being for those spreaders the discharge point (letter setting) still needs to be adjusted manually on the spreader itself.
The Kverneland fertiliser spreader database with the most up to date spreading charts is always available online. The AutosetApp can connect to the fertiliser spreading database in two different ways. You can connect it to the online database via the IsoMatch Wireless WIFI USB adapter or download the most actual database from the website www.kvernelandspreadingcharts.com on an USB stick and upload the database directly into the IsoMatch Tellus PRO or IsoMatch Tellus GO+ terminal.
- Kverneland offers the ExactLine system or manual/hydraulic border spreading plate for border spreading. The ExactLine can be accurately set for all types of fertiliser and for all working widths. Operation is easy, no need to leave the tractor seat. For the HL, TL and TLX models the ExactLine can even be fitted on the left and right hand side of the spreader.
- With one-side boundary spreading the tractor is driven approximately 2 metres from the field border.
- With boundary track spreading the tractor is driving in the first tramline and is spreading to the border. The distance to the border is the half of the working width.
- The Border Spreading Indicator (BSI), indicates which border spreading device is active.
- The Exacta HL/TL(X) spreaders are also available mounted on a trailer frame.
- Central Hydraulic Drive as option available for the HL/TL(GEOSPREAD).
- Easy to assemble aluminium hopper extensions are available to increase hopper capacity.
- An easy to fold in and out hopper cover is as option available. Simple to fit! This can be the manual hopper cover or with the electrical version controlled via the tractor cab.
- Left/right shut off valve for spreading at half working widths is optional available.
- To ensure a consistent flow when spreading low quantities, the CentreFlow system is equipped with a fine application kit. Ideal for spreading low quantities, seeds and slug pellets.
- Delta shaped heavy duty grids are standard equipment of the Exacta HL/TL(X) spreader.
- Centre gear box with 2 input shafts for high and low disc speed settings is standard equipment of the HL/TL(X) spreader.
- Hopper emptying kit is optional available to easy get the last fertiliser out of your hopper.
- Easy calibration is done with the optional calibration container.
- Long lifetime LED lighting set, is optional for the EL, CL and CL-EW. For the HL, TL and TL(X) GEOSPREAD spreader is this standard equipment.
- The mud guards (option) protect the spreading disc against mud, water etc.
Increase capacity
The combination of a front and rear spreader will not only increase the total hopper capacity up to 6,000 or 7,000l, but also, it makes it possible to spread two different applications in one pass. This saves time and labour due to less passes, and also reduces soil damage.
There is a perfect weight balance with a (smaller) spreader on the front and rear, which means less ground pressure or soil compaction which can be especially helpful in wet conditions. In case there is no PTO shaft available at the front of the tractor, the central hydraulic driveline on the GEOSPREAD spreaders can be used.
With a front lighting set available as an option, the road lighting turns on the correct side if the spreader is located in the front of the tractor.
Accurate spreading pattern
Spreading two different fertilisers at the same time in one pass will increase nutrition accuracy. Two different fertiliser types, with different physical properties, can be applied with a correct setting to have a perfect spreading pattern. The result is an increased yield and cost savings on fertiliser.
Different combinations
All Kverneland spreader models, even with a different hopper capacity, can be combined in the front and the rear. However for the models where there is no ExactLine border device available for the left hand side spreading, there is a limitation in border spreading on the headland. In the Task Control (TC) on the ISOBUS terminal there is the possibility to select the front spreader and to enter the correct settings for the front spreader.
Increase efficiency
With the front and rear spreader combination and two ISOBUS terminals connected, much more is possible to save costs and increase efficiency! To minimise overlap, section control will automatically switch on and off sections on both spreaders. With the variable rate application on all the Kverneland GEOSPREAD spreaders it is possible to automatically adjust the application rate separately from the front and rear spreader. For even more precision, MULTIRATE applies multiple rates within a working width, independently from the front and rear spreader.